<ruby id="grzpk"><sub id="grzpk"></sub></ruby>
    <nav id="grzpk"><mark id="grzpk"></mark></nav>
    <form id="grzpk"><small id="grzpk"></small></form>

        <var id="grzpk"></var>
        1. 當前位置:網站首頁 > 新聞中心 > 行業資訊
          • 冷庫安裝的流程是怎么樣的,有哪些步驟?
          • 本站編輯:杭州克冷制冷設備有限公司發布日期:2021-06-23 19:32 瀏覽次數:

          相信很多想要安裝冷庫的公司對于冷庫是怎么安裝的充滿好奇。那么今天杭州了克冷制冷的周工程師就帶大家了解一下,冷庫安裝的流程是怎么樣的?有哪些步驟?今天小編就給大家普及一下知識。首先想說的是冷庫安裝是一個系統工程,主要分為冷庫庫板安裝、冷風機安裝、制冷機組安裝、制冷管道安裝、電控系統安裝、調試這幾個部分。這樣說的話,可能很多人都不明白是什麼意思,那么以下再詳細一點。
          I believe that many companies who want to install cold storage are curious about how to install cold storage. So today, Hangzhou gram cold refrigeration engineer Zhou will take you to know about the cold storage installation process is how? What are the steps? Today Xiaobian will give you the knowledge to popularize. First of all, I want to say that the installation of cold storage is a system engineering, which is mainly divided into the installation of cold storage board, the installation of air cooler, the installation of refrigeration unit, the installation of refrigeration pipeline, the installation of electric control system and the commissioning of these parts. Said so, probably a lot of people do not understand what is the meaning, then the following more detailed

          1. 冷庫設計的方案。一般是根據客戶的需求,冷庫建造廠家派工程師或技術同事和客戶詳細溝通后,現場確認后設計出合理的方案,其中包括:制冷系統的確定、庫房布局、材料、設備、配件的合理配置、電控、溫控的配置等等。
          1. Cold storage design scheme. Generally, according to the needs of customers, the cold storage manufacturer sends engineers or technical colleagues to communicate with customers in detail, and designs reasonable schemes after on-site confirmation, including: the determination of refrigeration system, the layout of the warehouse, the reasonable configuration of materials, equipment and accessories, the configuration of electric control and temperature control, and so on.

          2. 冷庫冷風機的安裝:冷風機的安裝位置最好在空氣循環最好的位置。冷風機應該與庫板之間保持一定的距離,一般要大于冷風機的厚度,例如冷風機厚度為 0.5m則冷風機與庫板之間最小距離必須超過0.5m方可。
          2. Installation of cold storage air cooler: the installation location of the air cooler is best in the best position of air circulation. A certain distance should be maintained between the air cooler and the library plate, which is generally greater than the thickness of the air cooler. For example, the thickness of the air cooler is 0.5m, the minimum distance between the air cooler and the library plate must exceed 0.5m.

          3. 冷庫制冷機組安裝:一般小型冷庫都安裝全封閉式制冷機組,而中大型冷庫則安裝半封閉制冷機組。在制冷機組安裝結束后需要安裝配套的油分離器,并加入適量機油,如果冷庫預設溫度低于零下15℃的話還應該加入冷凍機油。
          3 cold storage refrigeration unit installation: general small cold storage are installed with fully closed refrigeration unit, and medium and large cold storage is installed with semi-closed refrigeration unit. After the installation of the refrigeration unit, the supporting oil separator needs to be installed, and the right amount of oil should be added. If the preset temperature of the cold storage is lower than minus 15℃, the refrigerating oil should also be added.

          4. 冷庫管道的安裝:管道直徑必須滿足冷庫設計使用要求,并且與各個設備之間保持一定的安全距離,安裝位置也需要根據現場實際情況進行調整。
          4. Installation of cold storage pipeline: the diameter of the pipeline must meet the design and use requirements of cold storage, and maintain a certain safe distance from each equipment, and the installation position needs to be adjusted according to the actual situation on the site.

          5. 冷庫電控制系統的安裝:在各個連接點處都必須進行標記,方便日后維修、檢測;所以電線必須用綁線進行固定;做好防潮工作,防止電線進水導致短路。
          5. Installation of the electric control system of the cold storage: all the connection points must be marked to facilitate future maintenance and detection; So the wire must be fixed with a tie wire; Do moisture-proof work to prevent short circuit caused by water in wires.

          6. 冷庫的調試工作:冷庫調試時需要先對電源電壓進行確認是否正常,很多情況下用戶來電報修,都是因為當時電壓不穩不能正常啟動冷庫所引起的,然后檢查設備的開 閉情況,向儲液罐內注入制冷劑,然后運行壓縮機。
          6 cold storage debugging work: cold storage debugging needs to confirm whether the power supply voltage is normal. In many cases, the user calls for repair because the voltage is unstable and the cold storage cannot be started normally. Then check the opening and closing of the equipment, inject refrigerant into the liquid storage tank, and then run the compressor.

          7,售后的維護。冷庫制作完成后不是一勞永逸的持續使用的,還需要定期的保養與檢修。對于電路老化,密封不嚴,系統異常等問題要及時發現并做出維護,以保證冷庫使用的安全性。
          7. After-sales maintenance. Cold storage production is not sustainable use once and for all, but also need regular maintenance and repair. For circuit aging, lax sealing, abnormal system and other problems should be found and maintained in time to ensure the safety of the use of cold storage.

           

          關于冷庫安裝有很多是需要長期從業的經驗才能做的完善的,如果朋友們對于以上內容還有不懂的地方可以隨時來咨詢我們克冷制冷,我們會詳細為大家解答的。杭州克冷制冷致力于食品冷庫、藥品冷庫、商超冷庫、冷風柜、負壓風機等系列產品,憑借優異的實用性和節能效果,贏得了眾多客戶的青睞。歡迎您的咨詢合作。聯系電話 :13116798338祝經理 

        2. 在線客服
        3. 聯系電話
          13116798338
        4. 在線留言
        5. 二維碼
        6. 在線咨詢
          风流老太婆毛多大bbb,国产成人a片免费视频,被cao到腿软百合abo,义息のマゾ奴隷熟肉中文版